Topic

An interferometric Rayleigh scattering system was developed to enable the measurement of multiple, orthogonal velocity components at several points within very-high-speed or high-temperature flows. The velocity of a gaseous flow can be optically measured by sending laser...

The objective of this effort was to show that real-time aircraft control-surface hinge-moment information could be used to provide a robust and reliable prediction of vehicle performance and control authority degradation. For a given airfoil section with a control surface — be it a wing with an aileron,...

A generalized framework has been developed for systems validation that can be applied to both traditional and autonomous systems. The framework consists of an automated test case generation and execution system called Nemesis that rapidly and thoroughly identifies flaws or vulnerabilities within a system. By applying...

The frequency to voltage converter analog front end evaluation prototype (F2V AFE) is an evaluation board designed for comparison of different methods of accurately extracting the frequency of a sinusoidal input signal. A configurable input stage is routed to one or several of five separate,...

Faults in wiring systems are a serious concern for the aerospace and aeronautic (commercial, military, and civilian) industries. Circuit failures and vehicle accidents have occurred and have been attributed to faulty wiring created by open and/or short circuits. Often, such circuit failures...

Clock compensation for Gigabit Ethernet is necessary because the clock recovered from the 1.25 Gb/s serial data stream has the potential to be 200 ppm slower or faster than the system clock. The serial data is converted to 10-bit parallel data at a 125 MHz rate on a clock recovered from the...

Analog-to-digital converters (ADCs) are used in scientific and communications instruments on all spacecraft. As data rates get higher, and as the transition is made from parallel ADC designs to high-speed, serial, low-voltage differential signaling (LVDS) designs, the need...

A modified process yields lower levels of internal porosity for solder joints produced in reduced-gravity environments. The process incorporates both alternative materials and a modified procedure. The process provides the necessary cleaning action to enable effective...

A 3D networked, dense form of single-walled carbon nanotubes (SWNT) has been made through isotropic shrinking of a gel-like SWNT-water paste by very slow evaporation. Approximately 35 g of Raw HiPco nanotubes were cleaned by the method of soft baking (250 °C for 15 hours...

In response to the Columbia Accident Investigation Board report, a plug repair kit has been developed to enable astronauts to repair the space shuttle’s wing leading edge (WLE) during orbit. The plug repair kit consists of several 17.78-cm-diameter carbon/ silicon carbide (C/SiC) cover plates of...

The purpose of the invention is to covalently attach functionalized carbon nanotubes to silicon. This step allows for the introduction of carbon nanotubes onto all manner of silicon surfaces, and thereby introduction of carbon nanotubes covalently into...

Newly developed magnetic devices are used to create an interface between adjacent mirror segments so that once assembled, aligned, and phased, the multiple segments will behave functionally equivalent to a monolithic aperture mirror. One embodiment might be a kinematic interface that is reversible so...

Transpiration-cooled fasteners are proposed that operate like an open-loop heat pipe (self-tapping screws, bolts, and spikes) for use in on-orbit repair of thermal-insulation of a space shuttle or other spacecraft. By limiting the temperature rise of such a fastener and of the adjacent...

The aperture ion source was conceived to eliminate distortion in measurements of angular distributions of neutral atoms and molecules that require electronimpact ion sources. The approach simplifies the coupling between ion source and spectrometer while providing virtually distortion-free angular distributions and improved...

Generic, object-oriented fault models, built according to causal-directed graph theory, have been integrated into an overall software architecture dedicated to monitoring and predicting the health of mission- critical systems. Processing over the generic fault...

Check out the newly redesigned Jan/Feb issue of Lighting Technology. Cutting-edge research news, industrial lighting application stories, feature articles, products, and new technologies for license help bring in the new year.

One day in 2010, a Rutgers physicist watched a store employee showcase a kitchen gadget that vacuum-seals food in plastic. The simple concept – an airtight seal around pieces of food – just might apply to his research: developing flexible electronics using lightweight organic semiconductors for...

A low-cost smart paint detects microscopic faults in wind turbines, mines, and bridges before structural damage occurs. The environmentally-friendly paint uses nanotechnology to detect movement in large structures, and could shape the future of safety monitoring.The paint is formed using a recycled waste...

According to a New York Times article, a band of astronomers recently restarted the search for extraterrestrial life, after an appeal for financing. Last spring, the University of California’s Hat Creek observatory, a collection of radio telescopes that listen for radio broadcasts of...

In the microgravity environment of the International Space Station (ISS), telling the difference between an actual fire and a false alarm may not be simple. To understand how to detect smoke in space, researchers from NASA's Glenn Research Center flew the Smoke Aerosol Measurement Experiment (SAME) aboard the...

A team of scientists from the University of Nevada, Reno, installed fiber-optic distributed temperature sensing equipment to conduct long-term monitoring of climate change effects on the Ross Ice Shelf in Antarctica and its potential for collapse. The equipment continually...

A Battery Management System (BMS) manages Lithium-Ion (Li-ion) batteries in a storage system for pulsed power weapons aboard Naval vessels. The system charges the batteries with a buck converter and uses analog equipment to measure signals. It then digitally converts signals for...

A recent partnership between the University of Southern California Viterbi’s Center for Advanced Transportation Technologies (CATT) and Audi’s Electronics Research Lab has provided USC with an Audi A8 fully equipped with a broad sensor suite that includes radar, lidar (for light detection...

UT Arlington engineers working with Army surgeons are developing a pliable, polymer mask embedded with electrical, mechanical, and biological components that can speed healing from disfiguring facial burns and help rebuild the faces of injured soldiers.The Biomask will be embedded with arrays of...

Scientists from the University of Bristol have developed a soap, composed of iron rich salts dissolved in water, that responds to a magnetic field when placed in solution. The soap’s magnetic properties were proved with neutrons at the Institut Laue-Langevin, which result from tiny iron-rich clumps...