In medical device manufacturing, potentially flammable and hazardous chemicals such as acetone and isopropyl alcohol are often stored in 55-gal or larger drums for dispensing into smaller containers or at the point of use.
Given that many of these chemicals and branded formulations are flammable, hazardous, or potentially combustible, it is incumbent on the environmental, health, and safety directors to identify the best type of pump for liquids used in manufacturing to ensure that workers can use them safely.
The risks could not be higher for medical device manufacturers. Utilization of the wrong type of pump or worse, employees tipping and pouring out contents, can be catastrophic. If toxic or highly flammable materials are accidentally released, it can lead to a corresponding spike in worker injuries, catastrophic fires, and even explosions.
Safety Data Sheets
When hazardous chemicals are brought into any facility, it must come in with the safety data sheets (SDS) and GHS-compliant labels. The Globally Harmonized System (GHS) was established by the United Nations to create a unified system for identifying and communicating critical information about hazardous chemicals.
Each SDS provides details about the potential environmental hazards, what to do in the event of small and large spills, and suggestions for treating injuries related to breathing in or coming into physical contact with chemicals are outlined. An SDS also identifies required personal protective equipment (PPE) and safe storage guidelines.
For flammable and combustible liquids specifically, the information in the SDS is vital to worker safety. Depending on the chemical substance, an SDS can include descriptions of severe injuries, transgenic damage to cells and organs, and even the alarming possibility of fatalities associated with the chemical.
For example, the SDS for acetone, a widely used solvent, includes mention of its “extreme flammability” and how it “burns with yellow bright flames.” In addition, “vapors can flow along surfaces to distant ignition sources and flash back… even minimal static discharge can ignite acetone vapors.”
With such potential consequences in mind, proper storage and handling is outlined in with the goal of preventing such dangerous situations from occurring. For flammable and combustible liquids, that advice is consistent across most, if not all, of the SDS. Recommendations include the following:
Avoid breathing fumes or vapors.
Keep away from heat, sparks, open flames or hot surfaces (for fear of ignition).
Keep containers tightly closed.
Bring in grounding or bonding devices for the container and receiving equipment.
Use explosion-proof electrical, ventilating, or lighting equipment (to prevent ignition sources).
Take precautionary measures against static discharge (another potential ignition source).
To punctuate the point further, most states and municipalities across the United States have adopted NFPA ® 30 Flammable and Combustible Liquids Code and OSHA 29 CFR 1910.106, which are fire codes that address the equipment, handling, storage, and use of flammable liquids.
Of course, this is only part of the solution. Ensuring the safe delivery of chemicals also requires proper safety training, the use of PPE, and, in some cases, further engineering controls.
Although an SDS does not state it directly, most — if not all — of these requirements indicate the need for a specialty pump for transferring flammable or combustible chemicals to smaller containers or at the point of use to maintain workplace safety.
Transfer Equipment Requirements
Whether mandatory or guidance, ensuring the safe transfer of these chemicals means implementing some type of sealed or closed-loop pump system that prevents vapors from escaping and ensures that chemicals do not come into contact with the person dispensing them. These systems should also be designed using materials and seals that can withstand extended contact with the chemical substance and must include grounding wires to prevent static discharge.
Such pumps are generally utilized throughout the medical devices industry. A sealed pump dispensing system enhances safety by eliminating spills and enables spill-free, environmentally safe transfer that also prevent vapors from escaping the container.
Because combustible and flammable liquids can easily be ignited by a flame, a hot surface, static electricity, or a spark generated by electricity or mechanical work, it is critical to eliminate external ignition sources when handling such liquids. Highly volatile solvents are even more hazardous because any vapor (VOCs) released can reach ignition sources several feet away and flash back to the liquid.
When transferring flammable liquids from large containers (>10 L), to a smaller container, the flow of the liquid can also create static electricity, which could result in a spark. Static electricity buildup is possible whether using a pump or simply pouring the liquid. If the bulk container and receiving vessel are both metal, it is important to bond the two by firmly attaching a metal bonding strap or wire to both containers as well as to ground, which can help to safely direct the static charge to ground.
For these reasons, containers used in the transfer of a Class 1 liquid (considered flammable with a flash point below 100 °F) and Class 2 and 3 liquids (considered combustible with a flashpoint above 100 °F) must be grounded or bonded to prevent electrostatic discharge that could act as an ignition source. NFPA 30 Section 126.96.36.199 also requires a means to prevent static electricity during transfer and dispensing operations.
Pump Selection Guidelines and Materials of Construction
Chemical compatibility guidance makes selecting the correct pump for each chemical or formulation in the medical device industry a straightforward task while maintaining workplace safety.
Given the variety of chemicals and branded formulations, it is critical to identify the correct pump for each application. Ultimately, this is often defined by the materials used to construct the pump that will come in contact with the chemicals. Each chemical has specific characteristics, so the selection of the appropriate gasket, housing, and hoses is important not only for safety, but also for longevity of the equipment. In addition, flammable liquids require a groundable pump, and food-grade liquids require a food-grade pump.
To find the right match, medical device manufacturers should work with a pump supplier to identify the right pump for the application. Established pump manufacturers compile detailed chemical compatibility databases that document the type of pump, gasket, and hoses along with whether the chemical needs to be groundable.
If the chemical is in the database, the pump often comes with a one-year warranty because either it has been tested or compatibility verified by the chemical manufacturer. When a chemical is not already on the list, the pump manufacturer will review the SDS and, if necessary, conduct tests to determine the right pump for the application.
Testing for Chemical Compatibility
Testing can be as simple as soaking the standard gaskets for 5–7 days in the chemical. Because vapors are volatile, they are frequently more harmful than the liquid itself. When appropriate, vapor tests are conducted in which the elastomer gasket options (e.g., Viton, EPDM, nitrile, and Santoprene) are suspended over the liquid. Pumps are then fully built, tested with each elastomer, and, if none of the gaskets work for the application, Teflon or Kalrez gaskets are used instead.
With some complex aromatics, aliphatics, and flammable liquids, a plastic pump housing may also need to be tested. This test is a 60-days soak in the chemicals to see whether the parts swell or bind with each other, which will cause the pump to fail.
The bottom line for medical device manufacturers is that the dangers of transferring flammable and combustible liquids are very real. By following the recommendations of the NFPA, OSHA, and other regulatory bodies, personnel can avoid hazards outlined in an SDS that could lead to physical injuries, chronic respiratory ailments, and even death.
Fortunately, protecting medical manufacturing workers from harm can be relatively straightforward with proper safety training, the use of PPE, and the use of engineering controls to prevent dangerous spills and chemical accidents.
This article was written by Nancy Westcott, President of GoatThroat Pumps, Milford, CT. For more information, visit here .