Features

The structures of most medical devices are far too complex to mold as a single piece. Therefore, it is necessary to assemble their components into a finished product. While this may be done with mechanical fasteners or adhesives, plastic welding may offer significant advantages. This article discusses two important plastic welding technologies: ultrasonic welding and laser welding and their implications for medical device designers and manufacturers.

Ultrasonic Welding: How It Works

In ultrasonic welding, high-frequency vibrations are applied to two parts or surfaces by a vibrating tool, commonly called a horn or sonotrode. Welding occurs as the result of heat generated at the interface between the parts. The ultrasonic vibrations are created by a series of components — the power supply, converter, booster, and horn — that deliver mechanical vibration to the parts.

As seen in Figure 1, the power supply takes a standard electrical line voltage and converts it to an operating frequency (in this illustration, 20 kHz). This electrical energy is sent through a radio-frequency cable to the converter. The converter uses piezoelectric ceramics to convert the electrical energy to mechanical vibrations at the operating frequency of the power supply. This mechanical vibration is either increased or decreased based on the configuration of the booster and horn. The proper mechanical vibration, known as amplitude, is determined by an applications engineer and is based on the thermoplastic materials used in the parts.

In operation, mechanical vibrations are delivered to the parts to be welded. The parts also are put under a mechanical load, generally with a pneumatic actuator that holds the booster and horn. Under this load, the mechanical vibrations are transmitted to the interface between the material surfaces, which focuses the vibration to create intermolecular and surface friction. This friction creates heat and a subsequent melt, which solidifies into a welded bond.

Converting electrical energy into ultrasonic welding energy.

Ultrasonic welds are widely used to join thermoformed plastic assemblies in medical devices because they eliminate the need for chemical solvents and adhesives, which can raise biocompatibility concerns, and they eliminate the need for mechanical fasteners. The ultrasonic welding process integrates easily into high-volume part production and automation because weld cycles are so fast — typically less than two seconds — and no consumables are required. Minimally invasive surgical instruments, including catheters, cannulas, luers, and trocars, often utilize ultrasonic joining with great success. For example, components that make up the sealing mechanism of a surgical trocar (see Figure 2) are ultrasonically welded into one sub-assembly of the finished product.

Many thermoplastics, both amorphous (such as polystyrene) and semi-crystalline (such as nylon), can be ultrasonically welded. In ideal situations, both parts in a weld are made of the same material. However, dissimilar plastics can also be ultrasonically welded if their melting temperatures (e.g., glass transition temperature, Tg), are similar.

This surgical trocar utilizes an ultrasonically welded sealing mechanism.

Typical plastic component designs require only minor modification to ensure repeatable, high-strength ultra-sonically welded assembly. The most common (and often “mold safe”) modification adds a small, triangular energy director to one of the mating parts surfaces (see Figure 3) and a corresponding textured surface on the opposing mating surface. The energy director melts and flows to join the two surfaces. Under ideal conditions, polymer chains from each side of the mating parts migrate across the interface and become indistinguishable from the parent material. The result is a bond that is comparable in strength to the parent material.

Energy director (the triangle) shown on upper mating part surface.

An Even Cleaner Alternative: Laser Welding

The market for in vitro diagnostics and implantable medical sensors, analyzers, and drug-delivery devices is exploding. But in applications like these, where the vibration required for ultrasonic welding might be undesirable, laser welding is often the best alternative. It provides a cosmetically attractive connection without causing deformation of intricate features or small parts. It also creates hermetic seals between small parts generating minimal flash or particulates, a quality essential to products that require cleanroom-quality assembly and packaging and that are trusted to deliver precise drug delivery therapies.

Simultaneous Through Transmission Infrared STTIr welding. Heat transferred across the interface and transmissive layer melts.

Unlike the ultrasonic method described earlier, laser welding does not introduce mechanical motion between the components being welded. Instead, the near infrared heat needed for part welding is provided by a laser light source. With no relative movement between the parts, weld alignment and part-to-part sealing is exceptionally precise. Welds are fast and clean, with minimal particulate and flash.

A Branson 3G laser welder.

A Branson innovation to laser welding, called Simultaneous Through Transmission Infrared welding (STTIr), is the first laser welding technology that can illuminate the entire welding surface at the same time. This approach eliminates the need to move or scan heat sources along the length of the weld and thus dramatically speeds up the laser welding cycle, reducing it to as little as 1–2 seconds on small parts. The exceptional cleanliness and precision of laser welding is the primary factor behind its recent and rapid growth in medical device, consumer electronics, high-end automotive, and business applications.

STTIr laser welding has certain part design requirements. First, one component of the assembly must be transmissive or have low absorbance of the laser wavelength to be used, while the mating component must be absorbent to that wavelength. Second, the geometry of the assembly must allow for delivery of the laser energy to the weld zone, where the melt occurs in the upper section of the absorbent part. There are many ways to bring laser energy to the weld zone. The illustration in Figure 4 demonstrates the fundamental concept.

« Start Prev 1 2 Next End»